Extech Instruments 411 Uživatelská příručka Strana 1

Procházejte online nebo si stáhněte Uživatelská příručka pro Multimetry Extech Instruments 411. Extech Instruments 411 User`s guide Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 14
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
User's Guide
True RMS Multimeter
Extech 411
Zobrazit stránku 0
1 2 3 4 5 6 ... 13 14

Shrnutí obsahu

Strany 1 - Extech 411

User's GuideTrue RMS MultimeterExtech 411

Strany 2 - Introduction

EX411-EU_ENG V4.0 5/0710TEMPERATURE MEASUREMENTS1. Set the function switch to the TEMP position.2. Insert the Temperature Probe into theTemperature So

Strany 3 - CAUTIONS

EX411-EU_ENG V4.0 5/0711SpecificationsFunction Range Resolution AccuracyDC Voltage(V DC)200mV 0.1mV(0.3% reading + 2 digits)2V 0.001V(0.5% reading +

Strany 4

EX411-EU_ENG V4.0 5/0712General SpecificationsDiode Test Test current of 1mA maximum, open circuit voltage 2.8V DCtypicalContinuity Check Audible sign

Strany 5 - Symbols and Annunciators

EX411-EU_ENG V4.0 5/0713MaintenanceWARNING: To avoid electrical shock, disconnect the meter from any circuit, remove thetest leads from the input term

Strany 6 - Operating Instructions

EX411-EU_ENG V4.0 5/0714REPLACING THE FUSESWARNING: To avoid electrical shock, disconnect the meter from any circuit, remove thetest leads from the in

Strany 7

EX411-EU_ENG V4.0 5/072IntroductionCongratulations on your purchase of the Extech 411 (part number EX411) True RMSMultimeter. This meter measures AC/D

Strany 8

EX411-EU_ENG V4.0 5/073CAUTIONS Improper use of this meter can cause damage, shock, injury or death. Read andunderstand this user manual before opera

Strany 9

EX411-EU_ENG V4.0 5/074OVERVOLTAGE CATEGORY IIIThis meter meets the IEC 610-1-2001 standard for OVERVOLTAGE CATEGORY III. Cat IIImeters are protected

Strany 10

EX411-EU_ENG V4.0 5/075Controls and Jacks1. Rubber holster2. 2000 count LCD display3. °F button4. °C button5. Function switch6. mA, uA and A input jac

Strany 11 - Specifications

EX411-EU_ENG V4.0 5/076Operating InstructionsWARNING: Risk of electrocution. High-voltage circuits, both AC and DC, are verydangerous and should be me

Strany 12

EX411-EU_ENG V4.0 5/077AC VOLTAGE MEASUREMENTSWARNING: Risk of Electrocution. The probe tips may not be long enough to contact thelive parts inside so

Strany 13 - Maintenance

EX411-EU_ENG V4.0 5/078AC CURRENT MEASUREMENTSCAUTION: Do not make current measurements on the 20A scale for longer than 30seconds. Exceeding 30 secon

Strany 14

EX411-EU_ENG V4.0 5/079CONTINUITY CHECKWARNING: To avoid electric shock, never measure continuity on circuits or wires that havevoltage on them.1. Set

Komentáře k této Příručce

Žádné komentáře